Guide

How to Use a Gas Weed Eater

Updated on · By the Dot Dirt team

To use a gas weed eater, fill the tank with the right fuel mix, start the engine with the choke on, and hold the head level just above the ground as you sweep the line into the grass. Keep the spinning head away from people, pets and hard surfaces, and let the engine idle before you shut it off.

On this page (9 sections)
  1. What do you need to have ready before you start?
  2. How do you start a gas weed eater from cold?
  3. How do you hold and move the trimmer for a clean cut?
  4. How do you edge a walkway with a gas trimmer?
  5. How do you trim around trees, beds and fences?
  6. What does a bigger trimmer do better?
  7. How do you shut down and cool the trimmer safely?
  8. Which trimmer suits which job?
  9. What are the most common mistakes with a gas trimmer?

To use a gas weed eater, fill the tank with the right fuel mix, start the engine with the choke on, and hold the cutting head level just above the ground as you sweep the line into the grass. Keep the spinning line away from people, pets and hard surfaces, and let the engine idle before you switch it off.

The first pass is about control, not speed. Once you know the cold-start order and the right angle, the rest of the job is steady, even sweeps around beds, fences and the driveway.

Knowing how to use a gas weed eater safely also means knowing when to stop and let the machine cool.

What do you need to have ready before you start?

Fuel mix, safety gear and a clear work area come first. A gas trimmer needs the right oil-and-gas blend, and running it dry of oil will ruin the engine.

Use fresh fuel mixed to the ratio the engine calls for, not straight gas. A 2-cycle engine needs oil in the fuel, so check our guide on what type of gas does a weed eater use if you're unsure about the mix.

Wear safety glasses, long pants and closed shoes. Clear toys, hoses and rocks from the lawn, because the line throws small objects fast and far.

Check the line spool and the guard before pulling the starter. A short or broken line cuts poorly and leaves a ragged edge.

How do you start a gas weed eater from cold?

Choke on, prime, pull until it fires, then choke off is the standard cold-start order. Husqvarna says its SmartStart system is built to cut the pull effort on the 122LK.

Start with the trimmer on the ground, flat and stable, with the head clear of the grass. Prime the bulb if the machine has one, set the choke to full, and pull the cord in steady strokes.

When the engine coughs or fires, move the choke to the run or half position and pull again. Let it idle for 10 to 15 seconds before you squeeze the trigger.

Don't hold the trigger while pulling the cord. A cold engine that revs straight away often stalls, and you repeat the whole start.

Who should look at the Husqvarna 122LK?

The Husqvarna 122LK suits a homeowner with occasional trimming around a modest yard. It's a 22cc 2-cycle engine with a 17-inch straight shaft, which reaches under shrubs and along fences without much bending.

The straight shaft gives it a longer reach than a curved model, and it takes Husqvarna's T25 head plus click-on attachments. That makes it a good fit if you want one powerhead for trimming and the odd edging or pruning job.

Skip it if you clear heavy brush or very tall weeds. A bigger engine and a brush blade suit that work, which is where the next pick comes in.

How do you hold and move the trimmer for a clean cut?

Hold the head level and parallel to the ground, with the line just touching the grass. Tilting the head gouges soil and scalps the lawn.

Stand with the trimmer at your side, not out in front of you. Swing from the hips in a smooth arc, and work in one direction so clippings fall behind you.

Move the head left to right along a fence line so the line cuts into fresh grass, not into the clippings you just made. Keep the engine speed high and steady rather than revving and letting off.

Don't push the head into the ground to force a cut. The line does the work, and buried line wears out fast and can break.

How do you edge a walkway with a gas trimmer?

Turn the head 90 degrees, run the line along the edge, and walk forward slowly. Edging gives a sharp line between lawn and pavement that a mower leaves behind.

Set the trimmer so the line spins against the edge of the walk, not across the top. Keep the head off the concrete surface so the line doesn't wear down on stone.

A straight-shaft trimmer makes this easier because you can rotate the head and keep the engine low. Curved-shaft models need the whole unit turned, which tires your arms on a long driveway.

Trim before you mow, not after. Edging first lets the mower pick up the clippings, and the finish looks cleaner.

How do you trim around trees, beds and fences?

Slow the sweep and shorten your stroke near anything you can't cut. The line damages bark, paint and bed edging if you run it at full pace.

Approach a tree trunk from the side and stop the head short of the bark. Keep a few inches of gap, then finish the grass around the base by hand or with a small tool.

For fences, run the line parallel to the panels and keep the guard between you and the wire. For beds, angle the head slightly away from the plants so clippings fly onto the lawn.

Don't use the trimmer to cut hedges, branches or vines. The line isn't built for woody growth, and you'll break line or stall the engine.

What does a bigger trimmer do better?

Clearing overgrowth and brush is the job a heavier machine takes on. A 52cc engine with a brush blade cuts tall weeds and dense growth that a light trimmer bogs down in.

The Wild Badger Power kit gives you an 18-inch string head for grass and edging plus a 10-inch brush-cutter blade. A shoulder strap joins the kit, and the full-crank 52cc engine is built for harder clearing than a homeowner model.

It starts within five pulls according to Wild Badger Power, and the powerhead accepts compatible Wild Badger Power attachments. The trade-off is weight: the unit is 24.2 lb, so a full afternoon of edging will wear on your shoulders.

Pick it if your yard backs onto rough ground or you clear a field edge each season. For a small suburban lawn, the lighter Husqvarna is easier to handle.

How do you shut down and cool the trimmer safely?

Release the trigger, let the engine idle, then stop it with the switch. Never set a hot trimmer down on dry grass or in the shed.

Let it idle for a minute so the engine settles, then use the on/off switch. A hot muffler and cylinder stay warm for several minutes, so set the unit on bare ground or concrete to cool.

Don't tip the trimmer on its side to check the line while the engine is hot. Fuel can spill from the tank, and the muffler can scorch the grass.

Once it's cool, wipe the guard, check the line, and top off the fuel before you put it away. Our guide on how to store weed eater in garage covers the right spot and the fuel question for long breaks.

Which trimmer suits which job?

Match the machine to the size of the job and the ground you clear. For most home lawns, a light straight-shaft trimmer handles edging, fences and beds.

Pick the Husqvarna 122LK for a normal suburban yard and a mix of trimming and edging. Pick the Wild Badger kit if you clear tall weeds, brush or a rough field edge.

Keep a spare line spool so a break doesn't end the session.

If you haven't bought yet, our guide on how to choose a weed eater walks through shaft type, engine size and weight. A cordless weed eater suits small yards with no fuel to mix, but it won't match a gas trimmer on overgrowth.

The short version of how to use a gas weed eater: fresh mix, a firm cold start, a level head and an even sweep. Do that and the trim line stays clean from the first pass to the last.

What are the most common mistakes with a gas trimmer?

Scalping, tilting the head and running old fuel cause most of the trouble. Each one is easy to avoid once you know the pattern.

Tilting the head digs the line into the soil and leaves a gouge. Holding it level keeps the cut even and the line lasting longer.

Old or wrongly mixed fuel is the top reason a trimmer won't start or stalls. Mix only what you'll use in a month or two, and don't leave fuel sitting in the tank through winter.

Revving the engine hard at start and forcing the head through thick grass also wear the machine. Let it warm up and move at a pace the engine can hold.

Finally, leaving the trimmer running while you talk or move obstacles is a safety risk. Shut it off when you stop cutting, and start it again when you're ready.

Frequently asked questions

How long does a tank of gas last in a weed eater?

Most homeowner trimmers run for 30 to 60 minutes on a full tank under normal load. Thick grass and a heavy cutting head burn fuel faster, so fill up before a big edge-and-trim session rather than mid-lawn.

Can I use a gas weed eater on wet grass?

It runs, but the cut is messy. Wet clippings clump and stick to the head and guard, and the line bogs down.

Wait for the dew to dry or the grass to dry after rain for a cleaner finish.

Do I need to wear safety glasses with a string trimmer?

Yes. The line spins fast and throws small stones, twigs and clippings, so glasses or a face shield protect your eyes.

Long pants and closed shoes add protection for your legs and feet.

Why does my gas weed eater stall when I squeeze the trigger?

The engine is likely still cold or the choke is set wrong. Let it warm up on half choke for 10 to 15 seconds, then move the choke to run before you rev it.

Old fuel mix is the other common cause.